Double Glazing Door Lock Repairs

Are your uPVC door or window doctor near me mechanism faulty? Maybe the handles on your uPVC windows and doors aren't aligned correctly or are difficult to operate.

It is crucial that your double glazed doors work smoothly, otherwise you'll be wasting energy and increase the chances of burglary. Owen the Locksmith can repair your door lock for a reasonable price.

Snapped Key

If a key breaks within the lock, it can be extremely annoying. It can also be a security problem, as it may make you vulnerable to a burglar if the door is not locked. There are a few quick fixes you can try to fix the problem and make your door work again.

Be sure to remain calm. If you panic, you could end up pushing the damaged key piece further into the lock.

Next spray WD-40 or a different penetrating oil into the lock to make the broken piece slip out more easily. You can also use a screwdriver to help break up any pieces stuck that could be hindering the flow. If you're fortunate enough to have a little bit of the key left visible it, you can make use of a paperclip or other metal object with a thin surface to grab it and pull it out. Both of these methods work well, but be cautious not to push the damaged piece of the key further into the keyway.

Some paperclips have grooved edges which can be used as hook extractors. Jigsaw blades are also well for this. If you don't have any of these, you can bend a hook with needle-nosed pliers. You can also use a pair of tweezers grab and pull out the remaining pieces of broken keys.

If you're unable to pull the broken piece of the key out, try using a lock de-icer. It's usually available at most hardware stores. It works by freezing any moisture or ice that may be inside the lock.

If none of these solutions seem to work, it may be time to consult a locksmith. Fitlocks experts can solve problems like broken handles and broken keys with uPVC locks and door mechanisms. They can also modify your double glazing door mechanisms to allow them to operate more easily. You can book repairs to your double-glazing online or call us to discuss your needs.

Broken Cylinder

A broken cylinder is an immediate security risk. It's fortunately a simple repair for a professional locksmith to complete. A locksmith must tap the cylinder in order to fix it. This can be done using the hammer or other tool. However, the best method is to make use of a wire or a long match. Position the match or the wire's end close to the keyway. After that, the locksmith can strike the lock to crack it open. This is better than using a hammer, which can harm the lock.

The most common cause of cracks in the head of a cylinder is due to overheating. This can occur when the block and the cylinder head are made of different metals such as cast-iron and aluminum. Different metals can heat up and cool down at different rates. This can cause localised hotspots to expand more quickly than the rest.

Another possible cause of cracks in the cylinder is corrosion. If the cylinder head and the block of the cylinder are not properly maintained, this can cause corrosion or rust, which may cause them to expand at greater rates than they should. This could lead to cracks in the future.

If your uPVC window lock or door is stiff or requires an enormous amount of pressure to turn, it can be the result of several things. A faulty locking mechanism, misalignment, or the wear of the handle are typical causes of this problem.

Fortunately it's a simple and inexpensive fix for most double glazing owners. A professional locksmith should be able to solve this problem within an hour of arriving at your home. They can replace the locking mechanisms, or replace the window handles, and also change the gearboxes based on your specific needs. A skilled locksmith will always be able to provide you with a recommendation on the most cost-effective solutions for your home. They can even recommend upgrades to 3 Star security TS007 euro cylinders that will give you an additional layer of protection against burglars. It's a small price to pay for the security that comes from knowing your uPVC doors are safe.

Broken Handle

Window handle locks have complex mechanisms that wear out with time and usage, so it's no surprise they occasionally break. If yours is damaged, it can be difficult to determine the source of the problem and make sure that you repair it correctly.

Fixing the broken handle, regardless of whether it's the internal latch or locking mechanism will increase the security of your uPVC door and prevent draughts. When you aren't doing it right, replacing or repairing your handle can be very costly and may damage the door's frame and lock and frame, so it's worth spending some time to make sure you do it correctly.

With the window in the open position and the window open, loosen the screw that holds the handle with the screwdriver. The screw should be located on the inside of the backplate, usually covered by an eye-catching cap to conceal it for aesthetic reasons. It is important to not be able to replace any internal parts of the handle such as the plates and levers on either side. It is best to keep them in the same order so you can replace them when needed.

Then, turn the handle so it's at 90 degrees towards the window frame. Then, loosen the screw at the back of the handle which holds it to the internal spindle by using another screwdriver. Once the screw is loose, take the handle off and take out the broken spindle. Replace this with a new one, making sure it's the same length as the previous one (you can typically find these on the internet or in hardware stores) and securely screw it in the right place. Don't over tighten the screw as this can damage the handle and the window frame.

Close the handle and try it. It should operate smoothly and you'll be able to open your window once again.

Make sure to check that your uPVC window is shut correctly when you're working with the handle. If they're not closing correctly, you could encounter draughts or damp in your home. It could also affect the energy efficiency of your home. A local window company, such as Core Sash Windows, will be capable of adjusting the hinges on your window frames so they are able to shut properly.

Broken Spindle

It is more likely for the spindle to break than the handle. This is particularly common in uPVC tilt and turn windows. These windows require a handle that acts as a locking mechanism within the window frame. The handle is attached to a central rod which triggers a set of cams that look like mushrooms, they locks are inserted into the window frame. If the dead latch mechanism is not able to open when the handle is turned, it is possible that the spindle is broken, this can be an extremely frustrating issue.

Fortunately, Repair My Windows And Doors there are ways to fix this problem. A reputable locksmith can swiftly and efficiently solve the issue. A good locksmith can disassemble the window's handle using a tool to remove the wheel part where the spindle is located. This can be done without damaging the handle or causing other damage to the frame of the window.

After the wheel has been removed the technician can then inspect the spindle to determine what has caused it to break. This involves disassembling the spindle and inspecting each component, noting any wear or damage. This process is usually carried out by technicians in an environment that is clean.

Then, clean the damaged spindle. This will help remove any dirt or other debris that may be obstructing it from working normally. After this the spindle can be repaired or Repair My Windows And Doors replaced. If it's being replaced, the technician could use a dowel of a similar size to the one used in the first and drill mating holes into both parts of the spindle. This will ensure that the new spindle is a precise fit with the handle.

If the damaged spindle is beyond repair My Windows and doors, it could be necessary to replace it entirely. Home centres sell generic substitutes, but if your window style is rare you'll need to contact an expert in cabinet making or woodworking who can recreate the exact component. Once the new spindle is installed, it can be fitted to the handle by lining up the screw holes on the handle with the frame's existing screws. Once the new handle is firmly in place, you'll be able to operate your uPVC window.